Eft infrared laser

Eft infrared laser DEFAULT

Flashlights and lasers can be extremely helpful in Escape From Tarkov, but in classic EFT fashion, their usage and benefits are left completely for you to figure out.

Escape From Tarkov : Flash light Guide

Using Flashlights and Lasers

With default controls
&#; Pressing T will toggle any lasers or lights on your weapon one and off.
&#; Pressing Ctrl+T will cycle between different modes depending on the device.

Depending on the device you have installed, you’ll also have access to different modes.

Combo units like this can include a visible laser, a normal flashlight, an IR laser, and an IR flashlight.

What’s the difference?

Currently, lasers will both give you a bright beam showing you where your weapon is actually pointed, and actually grant a slight buff to your recoil handling. Lasers must be on to grant this buff, and having multiple lasers does not grant a stronger effect. Also note that lasers are offset from the barrel of the gun, and so at very close distances your bullet will not land exactly where the laser is. For example, a laser mounted on the left of a gun will be pointing slightly to the left of where your shot will actually land in a close range fight.

Flashlights do not give a recoil buff, but are just very handy for seeing in dark buildings. Unfortunately, both lasers and flashlights are also very good at giving away your position. Always be mindful of where you’re pointing your lasers and lights.

Night Vision and Infrared

Infrared versions of lasers and lights will appear as a dim red that serve two purposes. With night vision equipment on, IR lasers and lights will be bright as day and serve not to give away your position to those without night vision.

&#; Pressing N will toggle night vision gear on and off.

But even without night vision equipped, IR lasers still grant a recoil handling buff without letting your opponent know what door you’re watching, andIR flashlights can also be handy for giving yourself a very dim light in dark areas without shining a bright light through every window you pass.

Sours: https://playerassist.com/flash-light-escape-from-tarkov/

Mounting an IR Laser on Your M-4 Carbine: You’re Probably Doing It Wrong

The most popular place to mount an IR laser on a carbine or rifle is 12 o’clock, top rail, up front towards the muzzle. It is a safe bet that about 95% of Special Operations run their lasers this way. The primary reason for this? So that the laser will not be obstructed by the front sight post or back up iron sights. Many shooters prefer to use the button on the laser itself, so they mount the laser so that it is where their support hand grips the carbine.

The other 5%, including myself, prefer to run it towards the receiver end of the rifle, mounted right in front of the optic. When people see this, it seems to confuse a lot of them, often generating a lot of comments such as:

  • &#;The IR laser will be blocked and not work at all.&#;
  • &#;One cannot zero it properly mounted that far back.&#;
  • &#;There will be too much shadow produced by the front sight or forearm making it very hard to make out the laser beam or flood.&#;

Of course, if this were true, I would not run it this way. Believe it or not, it works just fine. In fact, I have found mounting it towards the rear, behind my support hand to be the ideal place. I came to this conclusion during multiple tours to Afghanistan. Running it in the rear not only facilitated my primary method of holding the rifle, but more importantly, supported the most prevalent conditions I could expect to find myself in during firefights.

Dispelling Myths

Here are the most common questions and comments I get about my IR laser placement:

The laser will be obscured by the front sight post.” &#; This belief comes from the older PEQ-2 that has a less defined beam. Because of its length, it needed to be mounted as far forward as possible to fit on a carbine handguard. Most if not all current aiming lasers, still have the aiming laser offset on the right to avoid the front sight post.

Regardless if it is mounted towards the front or back, the front sight post does not interrupt it. Now it can still affect the IR flood, causing some shadowing, but that depends how you set the IR flood. If you set it for room distance with an extremely wide circle, then there will be shadowing on one side. I prefer to set the IR flood to appear as a six-foot circle at about 50 yards. That is a pretty tight cone.

I do not use IR flood to illuminate rooms I am in, but rather to illuminate windows and doorways. The tight beam is perfect for this. Too wide of a beam washes out and you cannot see into things at greater distances. A six-foot-wide beam set for 50 yards accomplishes this regardless of where the laser is mounted on the rail; Side, top, rear, or forward, it is not affected too much by the front sight post (if there is one) or the rail.

Zeroing issues? To tell the truth I stopped performing live-fire zeroing of the IR laser years ago. A 25 or 50 yard zero it not as accurate as co-witnessing the IR laser to the primary optic at an object of yards or more. The intent of a short range zero is to set the IR laser parallel to the bore of the carbine. That works fine, but I find its too time consuming. Let’s face it, no matter how well you zero, it is still only good for about yards or so due to bullet drop from gravity.

The laser goes out in a perfectly straight line for infinity; unfortunately bullets do not. I have found that aiming at something around yards away at dusk, then dialing the IR laser to touch it works just as well as live firing zeroing, regardless of the distance at which you dial it in. The point of aim (POA) of the laser and optic and the path of the bullet as it travels will be within a few inches of each to the point of impact.

That is perfectly acceptable combat accuracy. Zeroing your IR laser and optic at a specific distance works well at that distance. After that distance, the IR laser beam is now crossing the point of aim of the optic, causing the point of impact to move away as distance increases.

Dialing it in a dusk is also very handy. If you are using a LA-5 or LA, there is a good chance the tension screw that holds it onto the rail has come loose and the zero is lost. Re-dialing the IR laser to the primary optic before every mission corrects for this at whatever distance you expect to be shooting. I find this a lot more practical, than shooting it on a short range zero target. As far as mounting the laser on the side of the gun. I am not a fan of mounting it so the IR laser emits below the bore line. When I do mount it on the side, it is set so the IR laser emits top left. (It is still roughly within 2 inches of the bore and POA of Primary optic) plus being a lefty it is mounted opposite side of my support hand.

Why I Do It

In Afghanistan, the Taliban, insurgents, enemy, or whatever you want to call them, do not like to fight at night. It could be that they know we have superior night vision capabilities or because they lack their own night vision. Whatever the reason, it is not often that they will come out and fight at night.

The job of most Special Forces teams is to lead and advise Afghan partner forces. This usually comes in the form of leading Afghan Commandos or SF, on missions to find the enemy. Most of the time our missions would infill at night to avoid IEDs. At a pre-planned location we would hold up, fortify and wait for the insurgents to wake up, realize we are there and come at us.

Sightmark ReadyFire IR6: Stay on target in complete darkness!

Read Next: Sightmark ReadyFire IR6: Stay on target in complete darkness!

Another method was to run daylight movement to contact patrols. If you wanted any chance of finding and getting the enemy to come out, it had to be during daylight. While we mostly moved during darkness, the reality was 95% of the time, the action I saw was during the day. Because of this. I wanted my rifle set-up to facilitate when I saw the enemy the most, day time.

I shoot best running a C-clamp support grip. Although it does not bother a lot of Operators, I don’t like having to grip around the body of a LA I don&#;t find it is as stable or as comfortable as gripping around the rail alone. I like the IR laser mounted in the rear to keep it out of the way so that I have the optimum grip allowing me to shoot my best during daylight.

Does that block the IR laser if I had to use it? Yes, it does. To operate the IR laser, I would either run a pressure pad switch on a vertical foregrip or move my hand back to the laser and use the built-in button. Running my hand back or holding onto a vertical foregrip was not as stable for me as a C-Clamp grip. Most of us, when using lasers, do not get a perfect cheek to stock position.

Using the laser, most shooters shoulder the carbine and look over the gun focusing on balancing the laser on the target. A perfect body position and grip is not as important. Since you are indexing off the laser beam and not an optic or sights and breaking shots when you see the laser fall onto the target.

Why not just run it in front of your support hand? That exposes the IR laser to muzzle blast from the weapon and increases the likelihood of damaging the laser and will cause carbon build up on the lens. If you don’t regularly clean it, the laser will become blocked. I don’t want to have my laser disappear in a fight because it was obscured by carbon.

If you do anything that requires you to use the muzzle to strike with such as breaking glass or muzzle punching a threat, there is a chance you can knock it loose or damage your laser. The best reason to mount it reward is to help balance the gun. Although most lasers do not weight much, mounting it closer towards the middle avoids a front heavy gun that does not point well..

 

The Wrap Up   

If you are doing something a certain way that works for you, by all means, keep doing it. But if you are doing things because that is the way everyone says to do it, or that&#;s “just how it is&#; then I encourage you to experiment to find the best method for you.

Running an IR laser in the rear, while not the conventional method, is ideal for maximizing my combat effectiveness. Next time you hit the range, don’t be afraid to switch things up. You never know, you might surprise yourself.


by Jeff Gurwitch

Jeff has served 26 years in the U.S. Army, 19 of those in Special Forces. Currently, he teaches shooting part time and is contributing writer for SWAT Magazine and defensereview.com. You can find him on Instagram and facebook @ Modern Tactical Shooting

If you enjoyed this article, please consider supporting our Veteran Editorial by becoming a SOFREP subscriber. Click here to get 3 months of full ad-free access for only $1 $.

Sours: https://sofrep.com/gear/mounting-ir-laser-carbine-youre-probably-wrong/
  1. Charging nexus 6p
  2. N3 vocabulary
  3. Morro dunes reservations

AN/PEQ-2

The AN/PEQ-2 Infrared Target Pointer/Illuminator/Aiming Light (ITPIAL) is a laser sight for use on rifles fitted with a Picatinny rail. It was manufactured by Insight Technology.[1]

History[edit]

U.S. Marines in November armed with M16A2 rifles equipped with AN/PEQ-2s.

The AN/PEQ-2 succeeded the AN/PAQ-4C, which was designed in the early s after the Persian Gulf War.[2]

The device, which is mil-spec, is still seeing active service but is being withdrawn and replaced amongst U.S. Armed Forces. It was also part of the U.S. SOPMOD kit, though the device is being replaced by the new smaller AN/PEQ (ATPIAL) model.[3]

Operation[edit]

The AN/PEQ-2 has two infrared laser emitters&#;one narrow beam used for aiming the rifle, and one wide beam used for illuminating targets, like a flashlight.[4] The beams can only be seen through night vision goggles.[4] Each beam can be zeroed independently, and the illuminator's radius is adjustable. The two lasers are tied into one 6-mode switch, which has the following modes:

Mode Marking Targeting laser IR illuminator
0 OFF off off
1 AIM low power off
2 DUAL LO low power low power
3 AIM HI high power off
4 DUAL LO/HI high power low power
5 DUAL HI high power high power

Turning the mode switch does not turn on the lasers. A recessed button on top of the device is tapped once to briefly turn on the lasers or tapped twice to turn the lasers on until deactivated, either by pressing a third time or by turning the mode switch to off. Additionally, an extra pressure switch can be plugged into the rear of the device and then placed virtually anywhere, limited only by the length of the pressure switch's cord; typically one to two feet. This pressure switch operates the same way as the recessed button.[5]

The AN/PEQ-2A upgrade incorporates a blue removable safety block which physically prevents turning the mode switch to any of the high power modes, which are capable of causing eye damage. Both variants are waterproof to a depth of 20 meters and run on two AA batteries. Additional civilian variants also exist&#;they can provide greater power, visible/IR laser combinations, or other features.[5]

External link[edit]

References[edit]

Sours: https://en.wikipedia.org/wiki/AN/PEQ-2
Escape From Tarkov - Lasers Guide / Comparison vs BIS modded setup / A breakdown and full test

.

Laser eft infrared

.

EFT IR laser/luminator problems

.

Now discussing:

.



459 460 461 462 463